Blog

Paper Mache Bunny

A papier mâché bunny has been on my mind for a while now. I considered what to use for the bunny’s base.

How To Make A Snowman You

The newspaper sleeves I used for the papier mâché snowmen, and the plastic grocery bags used for the pumpkins would not work for the bunny. Balloons came to mind.

Papier-mâché Pumpkins and How To Paint on MyHumbleHomeandGarden.com

You can imagine that regular balloons would make a pretty big bunny. The bunny I was planning to create would be a more diminutive version. We always seem to have bags of water balloons for the kids. Imagining that these would be more in line, I blew up and tied a couple of them. The one for the body was inflated more than the one for the bunny’s head. Can you believe that this is how the bunny began? To make your own, follow the directions below.

How To Make An Adorable Papier Mâché Bunny
Use water balloons for a base.

I just finished an e-Book with all three of the paper mache bunny posts included. It includes the smaller recipe for paper mache clay and takes you step-by-step from the balloon base to how to paint your bunny. Click below for your own copy.

Paper Mache Bunny eBook
DIY Paper Mache Bunny E-Book

Papier Mâché Bunny Supplies

(We are an Amazon affiliate and may receive a small percentage of any sales through the links in this post at no cost to you. Thanks for supporting this website!)

For this project, you will need:

  • papier mâché paste ◄Click here for the recipe.
  • papier mâché clay ◄Click here for the recipe.
  • water balloons
  • newspaper
  • tape
  • corrugated cardboard
  • scissors
  • floral wire (22-gauge)

For this Papier Mâché Bunny, you clearly won’t need the quantity of paste and clay this recipe makes. You can half or quarter the recipe if you are only planning on making one or two of these. *Warning – These are addictive and you might want to keep making bunnies, snowmen, and pumpkins. You might need a large quantity! Just store the clay and the paste in a cool place. For 1/4 recipe, ◄click here.

Papier Mâché Bunny How-To

Take two water balloons and blow up one to make the body shape. Secure with an overhand knot. Inflate another balloon with less air to mimic the shape of the bunny’s head and secure it with another overhand knot. Using masking tape, tape the balloon head to the larger balloon on both sides of the two balloons.

How To Make An Adorable Papier Mâché Bunny on MyHumbleHomeandGarden.com

Cut strips of newspaper. You will want to make these smaller than the ones used for the bigger pumpkins. Depending on the size of your project, pumpkin, snowman, or bunny, you will want to cut the strips bigger or smaller to better fit the size and conform to the shape that you are covering. These strips are about 1/2″ wide by 5″ long. Don’t get overly crazy and make each one the exact size! You can see some of the strips on the head and neck area were smaller so they would lie flat on the balloon.

Using the papier mâché paste, adhere the strips of newspaper to the balloons in starburst patterns. The starburst pattern helps the dry product to hold together better, making a better foundation. Start this process where the two balloons were taped together, creating a “neck” and securing the two together.

You will want to move quickly to cover the balloons in the paper strips on this project. The possibility of the balloon popping was ever-present in my mind. With the pumpkins and the snowmen, wadded-up newspaper helped retain the shape. The balloons don’t have that support.

How To Make An Adorable Papier Mâché Bunny
Cover the balloon base with paper mache strips

Completely cover the balloons in at least 3 layers of newspaper strips. You can see that the knotted balloon opening was left visible. After the newspaper strips have completely dried, snip the mouth of the balloon off with scissors.

Ears and Arms Armatures and Cardboard Feet

With the florist wire, create a bunny ear shape, allowing some extra wire to insert into the papier mâché head. Twist the wire ends together.

I pierced two holes in the paper head where one of the loose wires could be slipped through one and fished through the remaining hole. In doing that, the wire cut the paper between the two holes. So, I twisted the loose wires together and slipped them through the slice. (In retrospect, instead of holes, a slit would have done just as well, if not better.)

How To Make An Adorable Papier Mâché Bunny
Use wire to create an ear shape.

Using masking tape, support the wire ear shape at the base. Repeat for the second ear. You can manipulate the wire to be whatever shape and position you want.

Cut two bunny foot shapes from the corrugated cardboard.

How To Make An Adorable Papier Mâché Bunny
Wire shape for ears and cardboard feet

Using masking tape, tape the cardboard feet to the lower end of the rabbit’s body. He should be able to stand briefly, however, you need to support the tape with some of the paper clay at this point.

How To Make An Adorable Papier Mâché Bunny
Tape the feet to the bunny body

Utilize Knowledge From Experience

When I was making the first pumpkins, it didn’t take long to figure out that these paper clay shapes need support at the bottom first. The upper half of one of the early large pumpkins shifted when it became top-heavy. All of the pumpkins that followed were turned upside down and a solid base was created first. The clay was allowed to dry, then, turned over, and from the bottom to the top, the clay was applied. Clay can be applied to the larger ones a third at a time to err on the side of caution.

The water from the wet clay can be absorbed into the paper strips, weakening them. Too much at once can be a bad thing.

How To Make An Adorable Papier Mâché Bunny on MyHumbleHomeandGarden.com

Reinforcing The Foundation

Pack clay between the body and the cardboard feet creating a good foundation. After this, the Papier Mâché Bunny should be able to stand on his own.

Add a light coat of clay to the lower half of the body and allow this to dry. The arms need to be added during the next step, so, leave that area free of clay.

Add some of the paper strips to the ear wires. Allow these to dry a little bit. Then, add more to cover the entire opening on each ear shape. Remember, some of the strips should partially cover the ear and extend onto the head. Extra strips can be applied over those to secure the ears to the head and make a more stable ear.

Armature For Bunny’s Arms And Paws

How To Make An Adorable Papier Mâché Bunny
Armature for the bunny

Take the paddle wire and create an armature for one of the bunny’s arms and paws. You can see in the picture that the wire was doubled back on itself, creating one shoulder, arm, and paw. Then, the loose end was threaded through a slit on one shoulder and through a slit on the other shoulder.

How To Make An Adorable Papier Mâché Bunny
Armature for the arms and paws

After being threaded through the second slit, shape the wire into a matching armature for the other arm and paw. The excess wire can be cut off at the end. Use masking tape to support the wire where it meets the papier mâché. Bend the wires into the shape and position you want for each of the arms and paws.

How To Make An Adorable Papier Mâché Bunny on MyHumbleHomeandGarden.com

The Paws For The Papier Mâché Bunny

Start covering the armature for the paws with paper strips. (I use a paintbrush to cover the strips with glue on both sides. You can dip it in the glue if you like and squeeze the excess off but I like the less messy process of using the paintbrush.) Let that dry while you work on the upper part of the arm, covering it with strips of paper. Next, cover the other arm in the same fashion.

How To Make An Adorable Papier Mâché Bunny on MyHumbleHomeandGarden.com

Once the second arm is covered in paper, go back to the first one and add another layer of paper strips. Repeat with the second arm.

How To Make An Adorable Papier Mâché Bunny
Add another layer of paper strips.

Patience Required For Making This Papier Mâché Bunny

Add some more of the clay to begin to shape bunny feet and a more stable base. Add a thin layer of clay to the ears and the head. When I can’t pick the bunny up without putting my fingers in the wet clay already applied, I stop. Then, step away from the bunny and let him dry overnight. This takes patience but it is worth it.

I didn’t have an absolute idea of what this bunny would look like when this project began. His personality is beginning to take shape already. Does he remind you of the Velveteen Rabbit? I love his ears! This is part 1 of the Papier Mâché Bunny How To. Click here ►for part 2…

Be Social!

Follow me on Instagram, Pinterest, and Facebook so you won’t miss anything! I would love for you to share this post with your friends! They need amazing ideas, too! Pin it! It only takes a second!

How To Make A Papier Mâché Bunny
How To Make An Adorable Papier Mâché Bunny

List of Link Parties Where I Visit and Share Posts

  • Beautifully Made Link Party 70 for Crafts Home Decor andDIY Projects!
  • Wonderful Wednesday
  • Friendship Friday – Create With Joy
  • Friday Features Linky Party
  • Grammy’s Grid – Unlimited Monthly Linkup Party
  • Home Matters Linky Party
  • Saturday Shuffle at Strawberry Butterscotch
  • Interior Frugalista